APPLICATION:
Read and understand technical data sheet and associated safety data sheet completely before beginning installations. Always use appropriate personal protective equipment. Prior to beginning a project, apply in an inconspicuous area to test and become familiar with your complete application method and to ensure product satisfaction. Follow industry standards and flooring manufacturer’s recommendation for acclimation, design, layout, and application of wood flooring materials.
RECOMMENDED APPLICATORS:
Professional T-Bar/Pad, Roller, Paint Pad, or Brush can be used.
MIXING:
Use a stir stick, or rock container several times, to thoroughly mix and re-disperse any settlement.
Alternatively, shake well before using - then set aside for at least 20-30 minutes prior to use. It is important to stir (not shake) from time to time to prevent settling.
ADDING WATER:
Up to 12 ounces of potable water can be added per gallon of finish. Adding water will increase the flow and level time. (Particularly helpful when jobsite has higher temperatures or lower humidity.)
SURFACE PREPARATION:
Full sand prior to use. Sand floors using accepted NWFA/MFMA procedures.
PLEASE NOTE: After final sanding, be sure tore cord moisture readings throughout installation. Moisture readings during installation provide abaseline / benchmark for when to begin next application steps. Always make sure moisture is within acceptable levels for region of the project. Thoroughly vacuum floor prior to application. Tack with clean dry towels until all dust has been removed.
SEALER APPLICATION (PRE-APPLICATION):
Always maintain adequate temperature/ventilation during all phases of the coating and drying process.
• Restrict air flow during application to help prevent premature drying.
• Measure and record moisture content of floor in several areas.
• Rinse applicator and remove all excess water. This also helps to remove loose fibers.
FOR NEW INSTALLATIONS / NEWLY SANDED FLOORS:
Apply 1-2 Coats of GameDay Sealer, followed by 2 or more coats of approved Basic Coatings waterbased finish.
T-BAR APPLICATION: Pour a 4” wide line of finish along the starting wall. Using a clean,
pre-dampened T-Bar applicator, draw the applicator in the direction of the grain of wood at a slight angle. While keeping the wet edge in the middle of the T-Bar, move the finish puddle with the grain of wood, wall to wall. At the end of each run, turn the applicator towards you and pad out the applicator parallel to the wet edge. Feather out all turns and touch up any missed areas if seen right away.
ROLLER APPLICATION: Using a clean, pre-dampened microfiber roller, apply finish in the direction of the grain of wood. Apply evenly at the recommended coverage rate. Feather out during application to avoid streaks, puddles, lap and turn marks.
• Allow a minimum of 30-45 minutes to level.
• After sealer levels, allow increased and balanced air movement and fresh air exchange. Proper air movement will help dry the sealer.
• After a minimum 2-3 hours (under good conditions), re-measure moisture content. If moisture content is not equal to the first reading, allow more dry time.
• If necessary, abrade between coats to remove debris, hair, drips, etc. or if the 24-hour window between coats has elapsed. Abrade with the pad-and-strip system using 180 -240 grit sanding strips.
• Between coats, vacuum and tack with a Basic Coatings Microfiber Mop.
• When proper moisture content of flooring is achieved, application of compatible finish can begin.
APPLICATIONS OVER STAINS: Prior to sealer, apply compatible stains per manufacturer’s directions. This includes allowing the stain to dry completely. Solids content of stains, porosity of flooring, temperature, humidity, air flow, and other jobsite conditions dramatically affect dry times of stains. Always do adhesion test in inconspicuous area prior to starting project.
CLEAN-UP: Application tools should be thoroughly cleaned with water immediately after use.
DRY/CURE TIME: Allow at least 2-3 hours between coats. Once you increase air flow, keep air movement for several hours to ensure proper curing. Please refer to specific product technical data sheet for specific product information. In general, light foot traffic after 24 hours is acceptable. Furniture can be carefully replaced, however finish is susceptible to marring and scratching until the finish is fully cured - approximately 7 days. Do NOT place carpet, rugs, or cover the finish for at least two weeks after the finish has dried.
COVERAGE: Average of 450 - 550 sq ft/gal (11 - 13 sq m/l), depending on wood flooring species, porosity, and other jobsite conditions.
LIMITATIONS: Do not apply over acrylic or waxed surfaces.
Basic Coatings recommends using a NWFA/MFMA/Industry Certified Professional.
FLOOR CARE: Apply approved Basic Coatings waterbased wood finish per directions.